S1 | VISION, a Liebherr company
An S1 vehicle on the ridge of a point-cloud landscape

The S1mplest
machine
to
move material.

The S1 is a compact, battery-electric haulage vehicle that runs autonomously in confined industrial and underground environments.
It takes over the repetitive transport leg, so that loading equipment stays at the face and people stay off the haul route.

Whether you are looking to enhance productivity, increase safety, and reduce emissions, the S1 delivers on all fronts.

Explore the S1

S1 Characteristics

The S1 is designed for one job: moving material reliably where space, air quality and available people are the limiting factors.
Eight design decisions follow from that. Each one is listed below with what it changes for the operation.

Self-Levelling

The S1 keeps its load bed level and its
centre of gravity low, whatever the
load, the gradient or the state of the
road. Material stays secure on steep
ramps and uneven ground, with no
operator input. The vehicle adapts
to the environment rather than the
environment being prepared for the
vehicle.

Stable Position

Support feet extend and take the
vehicle off its suspension for loading,
dumping, charging and maintenance.
The result is a rigid stance that holds
under a full bucket, and full access to
every key component from ground
level.

Autonomous & Remote

The S1 drives autonomously, or if the
job calls for it, one operator
supervises several units remotely from
a single station. It navigates without
GPS, underground and on surface alike,
by matching live sensor data against
an onboard map of the route, with no
positioning infrastructure along the
way. A continuous, low-bandwidth link
carries the safety stop, job
assignments and route updates.
Positioning works independently of
that link. If the link drops or humans
are detected in the working area, the
S1 comes to a controlled stop.

Manoeuvrability

The S1 turns within its own footprint
and travels in both directions
equally well, with one driven axle,
no articulation joint and no trailer.
This removes the need for turning
bays and oversized intersections.
The vehicle is sized to the excavation
rather than the excavation being
sized to the vehicle.
Existing operations gain from
the same property. Cycles can be
reorganised within the development
already in place, with minor
adjustments instead of a redesign.

Battery Electric

Zero emissions at the point of work.
The battery-electric drivetrain
removes exhaust, heat and noise
from the working area, which lowers
ventilation demand, improves air
quality and cuts operating cost. Fewer
emissions mean less supporting
infrastructure and a lower cost per
tonne moved. We expect a working
cycle of six hours, with charging
adapted to the conditions on site.

Fleet Operation

The S1 is designed to work in
coordinated fleets rather than as a
single machine. Units share routes,
manage right of way between
themselves and keep the haulage
cycle running continuously. The result
is steady, predictable throughput
across the shift.

A tablet showing the S1 fleet control app

Individual Payload

The S1 platform is built around
a modular payload concept. The
standard configuration is matched
to common loading equipment in
a single pass. Alternative modules
adapt the platform to different
materials, densities, and operational
requirements — without redesigning
the base vehicle.

Uptime

Every major component is accessible
from ground level with standard
tooling, and the S1 is designed for the
maintenance team already on site.
Because the haulage task is carried
by several small units rather than one
large machine, a vehicle taken out of
service reduces throughput for as
long as it is down, instead of stopping
the cycle. Behind the platform stands
Liebherr’s service network, the same
infrastructure that supports heavy
equipment operations on every
continent.

Self-Levelling

The S1 keeps its load bed level and its centre of gravity low, whatever the load, the gradient or the state of the road. Material stays secure on steep ramps and uneven ground, with no operator input. The vehicle adapts to the environment rather than the environment being prepared for the vehicle.

Stable Position

Support feet extend and take the vehicle off its suspension for loading, dumping, charging and maintenance. The result is a rigid stance that holds under a full bucket, and full access to every key component from ground level.

Autonomous & Remote

The S1 drives autonomously, or if the job calls for it, one operator supervises several units remotely from a single station. It navigates without GPS, underground and on surface alike, by matching live sensor data against an onboard map of the route, with no positioning infrastructure along the way. A continuous, low-bandwidth link carries the safety stop, job assignments and route updates. Positioning works independently of that link. If the link drops or humans are detected in the working area, the S1 comes to a controlled stop.

Manoeuvrability

The S1 turns within its own footprint and travels in both directions equally well, with one driven axle, no articulation joint and no trailer. This removes the need for turning bays and oversized intersections. The vehicle is sized to the excavation rather than the excavation being sized to the vehicle. Existing operations gain from the same property. Cycles can be reorganised within the development already in place, with minor adjustments instead of a redesign.

Battery Electric

Zero emissions at the point of work. The battery-electric drivetrain removes exhaust, heat and noise from the working area, which lowers ventilation demand, improves air quality and cuts operating cost. Fewer emissions mean less supporting infrastructure and a lower cost per tonne moved. We expect a working cycle of six hours, with charging adapted to the conditions on site.

Fleet Operation

The S1 is designed to work in coordinated fleets rather than as a single machine. Units share routes, manage right of way between themselves and keep the haulage cycle running continuously. The result is steady, predictable throughput across the shift.

Individual Payload

The S1 platform is built around a modular payload concept. The standard configuration is matched to common loading equipment in a single pass. Alternative modules adapt the platform to different materials, densities, and operational requirements — without redesigning the base vehicle.

Uptime

Every major component is accessible from ground level with standard tooling, and the S1 is designed for the maintenance team already on site. Because the haulage task is carried by several small units rather than one large machine, a vehicle taken out of service reduces throughput for as long as it is down, instead of stopping the cycle. Behind the platform stands Liebherr’s service network, the same infrastructure that supports heavy equipment operations on every continent.

One platform, more
than
one application

Three S1 vehicles in an underground mine tunnel, the nearest loaded with ore, a wheel loader filling the third further down the drift

Mining

01

In narrow headings the tram is what keeps the loading unit away
from the face. The S1 takes that leg over, so the loader stays where
it earns its cost. Battery-electric operation removes emissions
and heat from the heading, and the compact single-axle format
fits drifts sized for the orebody rather than for the fleet. Higher
output from smaller machines.

Get Onepager as PDF Mining

Download Onepager Mining
An S1 vehicle on a building site beside an excavation pit, two more carrying soil behind it, a crane and new apartment blocks beyond

Earth­moving

02

Quarries, gravel pits and aggregate operations face two
converging pressures: fewer available operators and tighter
emissions rules. A fleet of S1 vehicles runs the repetitive haul
leg continuously, without a cab to staff for every unit. The S1 is
developed to work alongside Liebherr loading equipment and
equally alongside the machines already in the pit, whatever the
make.

Get Onepager as PDF Earthmoving

Download Onepager Earthmoving
Two S1 vehicles side by side in an empty hangar, one with a tipping body and one with a flat bed, roller doors behind them

Your
envir­onment

The S1 is a base vehicle with interchangeable payload modules,
which means the machine does not fix the application. Tunnelling,
industrial plants, materials handling on constrained sites:
wherever material moves along the same route repeatedly and a
person should not have to be there, the platform is a candidate.
The applications not yet thought of are the ones that interest us
most. Enquiries are welcome.

Get in touch

Get in touch

03

Company

A map of Switzerland with the company's location marked

S1 Vision GmbH is a corporate venture of the Liebherr
Group, based in Dübendorf near Zürich,
Switzerland.

We develop autonomous, battery-electric transport
platforms for environments where
conventional
equipment reaches its limits.

In the most demanding industrial environments, haulage
is still solved by people operating
machines in conditions
that are dangerous, expensive and increasingly hard to
staff. We are
building a new class of vehicle for exactly that
job, purpose-built for the places no one else
builds for.

We work with Liebherr’s engineering depth,
manufacturing capability and global service
network
behind us, and with the speed, focus and independence
of a start-up. The third
generation of the S1 is running at
Liebherr’s plant in Bischofshofen. First pilots are planned
for
2027, with series availability towards the end of 2027.

Get in touch

Interested in the S1 or want to learn more about autonomous haulage for your site?
Reach out — we’ll get back to you directly.

Contact information

Receive our Onepagers

Select the PDFs you would like to receive by email. Multiple selections are possible.

We will email your selected PDFs after you submit this form.